Download Torque Specs in Pdf Format
Download TSB 980202 on Engine bearing Specs in Pdf Format
Torquing with a Crowsfoot Wrench
| Axle Front / Rear | *Wheel (2-Piece Steel) | |||||
| Standard (ft-lb) | Metric (Nm) | Standard (ft-lb) | Metric (Nm) | |||
| Cover Bolt | 16 | 22 | Lug Nut, Tapered | 110 | 149 | |
| Drain or Fill plugs | 13-18 | 18-24 | Wheel Half Lock-nut | |||
| Halfshaft to flange* | 57 | 77 | Initial | 85 | 115 | |
| Mounting bracket to Housing Bolts | 125-150 | 169-203 | Final | 125 | 170 | |
| Output Flange LockNut | 166-196 | 224-265 | *Wheel (1-Piece Steel) | |||
| U-Joint to Pinion Yoke | ||||||
| 1/4" Fine Thread | 13-18 | 18-24 | Standard (ft-lb) | Metric (Nm) | ||
| 5/16" Fine Thread | 27 | 37 | Lug Nut, Flanged | 140 | 190 | |
| *Use special 2 piece locking washers (nord-loc's amg part number 06008029) | *Wheel (1-Piece Aluminum) | |||||
| Brake Caliper Front / Rear | Standard (ft-lb) | Metric (Nm) | ||||
| Lug Nut, Tapered | 110 | 149 | ||||
| Standard (ft-lb) | Metric (Nm) | *Wheel (2-Piece Aluminum) | ||||
| Bleed Screw | 6-15 | 8-20 | ||||
| Cable Braket Screws | 20-25 | 27-34 | Standard (ft-lb) | Metric (Nm) | ||
| Caliper Guide Pins | 30 | 41 | Lug Nut, Tapered | 110 | 149 | |
| Caliper Yoke To Adapter | 40 | 54 | Wheel Half Lock-nut | |||
| Lever Retaining Screw | 15-25 | 20-34 | Initial | 50 | 68 | |
| Geared Hub | Final | 75 | 102 | |||
| *NOTE: Torque bolts in proper sequence for each step (see owners manual) | ||||||
| Standard (ft-lb) | Metric (Nm) | |||||
| Access Cover | 15 | 20 | Beadlock / Runflat (Cam Style) | |||
| Access Plug, Half-shaft Bolt | 8-13 | 11-18 | ||||
| Drain / Fill plug | 8-13 | 11-18 | Standard (ft-lb) | Metric (Nm) | ||
| Halfshaft to Drive Gear Bolt | 37 | 50 | Beadlock Pinch Bolt | 60 | 68 | |
| Input Seal Plate | 30 | 40 | Runflat Cam Bolt (before cam adjust) | 1-7 | 1.4-9.5 | |
| Steering Cover | 65 | 88 | Runflat Cam Bolt (after cam adjust) | 45 | 68 | |
| Transmission and Transfer Case | Runflat (Cross Bolt Style) | |||||
| Standard (ft-lb) | Metric (Nm) | Standard (ft-lb) | Metric (Nm) | |||
| Torque Converter to Flywheel | 32 | 44 | Runflat Cross Bolt | 22 | 30 | |
| Transmission Case to Engine | 32 | 44 | Locking Clip Screw | 30-35 | 40-50 | |
| Transmission Drain Plug | 25 | 34 | Suspension | |||
| Transmission Pan | 12 | 16 | ||||
| T-case Drain / Fill plugs | 30-40 | 41-54 | Standard (ft-lb) | Metric (Nm) | ||
| T-case Output Yoke Locknut | 110 | 149 | Control Arm Bushing | 260 | 354 | |
| Steering System | Control Arm Bracket | 90 | 122 | |||
| Shock Absorber Bottom Bracket | 178 | 242 | ||||
| Standard (ft-lb) | Metric (Nm) | Shock Pin-Top/Bottom | 300 | 408 | ||
| Ball joint to Control Arm | Stabilizer Bar Link to Control Arm | 70 | 95 | |||
| 3/8 Fine Thread | 28 | 38 | Stabilizer to Bar Link | 75 | 100 | |
| 3/8 Coarse Thread | 37 | 50 | ||||
| 7/16 Coarse Thread | 65 | 80 | Key | |||
| Ball Joint To Geared hub | Pipe Thread Sealant | |||||
| Lower | 73 | 99 | Thread Locker Blue | |||
| Upper | 65 | 88 | Thread Locker Red | |||
| Idler Arm to Center Link | 80 | 108 | Anti-Seize (GM P/N 1052771) | |||
| Idler Arm to Frame - 7/16 Bolts | 60 | 81 | ||||
| Idler Arm to Frame - 12mm Bolts | 90 | 122 | ||||
| Intermediate Shaft to Steering Gear | 60 | 81 | ||||
| Pitman Arm to Center Link | 80 | 108 | ||||
| Pitman Arm to Steering Gear | 185 | 250 | ||||
| Steering Gear Mount Bolts | 60 | 81 | ||||
| Steering Wheel to Shaft | 35 | 47 | ||||
| Tie Rod End to Center Link or Hub | 70 | 95 | ||||
| Rear Tie Rod to Frame | 260 | 354 | ||||